Skip to main content
PCBFreeNewv1.0.0

RF 阻抗 PCB 评审

Altium RF 板阻抗评审工作流:从 Layer Stack Manager 取真实叠层,计算微带/差分阻抗,对照 50 Ω 目标与 RF 布局清单(过孔围栏、参考连续、连接器过渡)。

Installs: 0Rating: –Updated:
Claude CodeAltium Designer

Badges only claim the demo-run passed on that host; cross-host installation is handled by the adapter layer.

You say
Review the 50 Ω microstrip impedance on this Altium RF board using the real stackup; check the via fence and connector transition and give me a fix list.

Content matches the files inside the package; extracted by the publish pipeline.

RF 阻抗 PCB 评审

评审 Altium 中的 RF 板(2.4 GHz 及以下频段初评):受控阻抗 线是否命中目标、RF 布局是否合规。所有计算输入必须来自真实 板文件,禁止用"典型叠层"冒充。

1. 从 Altium 提取数据

  1. Layer Stack Manager:记录 RF 走线层到相邻参考平面的 介质厚度 h(mm)与介电常数 er(注意板厂给的 er 是频率 相关值,2.4 GHz 用板厂高频参数或实测)。
  2. PCB 面板:受控阻抗网络的线宽 w、差分对间距 s、走线长度。
  3. 叠层截图/导出与网络清单一并交给用户确认。

2. 阻抗计算

node scripts/z0_calc.mjs --er 4.3 --h 0.2 --w 0.35
node scripts/z0_calc.mjs --er 4.3 --h 0.2 --w 0.3 --s 0.15

输出单端 Z0(Hammerstad-Jensen)与差分 Zdiff(经验耦合公式, ±10% 量级)。命中判定:|Z − 50| ≤ 10%(或用户指定容差)。 边界值必须转场求解器/板厂测试条,见参考文档适用边界。

3. 布局清单评审

对照 references/rf-layout-rules.md 逐项核对:参考平面连续、 过孔围栏间距(≤ λg/20)、连接器过渡、无残桩、禁布区、 阻焊影响。每项记录 pass/n/a/action 与证据。

4. 交付

评审纪要(阻抗计算表 + 清单结论 + 整改建议)。action 项 整改后重算复检。提醒用户:首板必须做阻抗测试条与 VNA 实测(S11/插损),计算只是初评。

Rules

  1. 叠层与线宽只能来自真实 Altium 板文件;没有 Altium 环境时 明确告知用户如何导出,不得编造数据或结论。
  2. 不打印、不存储任何 API key;本 Skill 不需要第三方凭证。
  3. 2.4 GHz、CPWG 结构或毫米波:本包公式不适用,必须建议 场求解器,不得外推。

What you get

  • Impedance computed from the real Altium Layer Stack Manager stackup
  • Microstrip/differential impedance checked against the 50 Ω target
  • An RF layout checklist (via fence, reference continuity, connector transition)
  • Impedance deviation and fix suggestions

Good fit for

  • Pre-fab impedance review of Altium RF boards (WiFi/BT/sub-1 GHz)
  • Layout engineers computing from the real stackup rather than estimates
  • 50 Ω single-ended or differential RF traces

Not for

  • Non-Altium projects (stackup comes from Layer Stack Manager)
  • Antenna matching / Smith-chart tuning
  • Precise impedance verdicts without real stackup data
Before you start

You provide

  • Altium project stackup (Layer Stack Manager export)
  • Target impedance (default 50 Ω) and trace geometry
  • Local Altium ≥ 22 and Node ≥ 20

Environment

  • altium ≥ 22
  • node ≥ 20

Last tested

No demo-run record yet.

Dependencies

Demo run

No demo run
Demo artifacts and verification reports appear here once a package includes them.

FAQ

Ratings & reviews

Not rated0 ratings

5 star0
4 star0
3 star0
2 star0
1 star0

Sign in to rate this skill.

Sign in

Versions

  • v1.0.0Latest4.2 KB

    首发种子版本。

    License: MITSHA-256: bf6c572d82244cbd…

Related skills

No related skills
Skills with the same output type and use case will appear here.