Skip to main content
PCBFreeNewv1.0.0

ESP32 最小系统 PCB

ESP32-WROOM-32E 最小系统板的布局工作流:Strapping 引脚、EN 复位电路、天线禁布区与去耦摆放检查(KiCad pcbnew 脚本)。

Installs: 0Rating: –Updated:
Claude CodeJLC EDAKiCad

Badges only claim the demo-run passed on that host; cross-host installation is handled by the adapter layer.

You say
Check the strapping pins, EN reset circuit and antenna keep-out on this ESP32-WROOM-32E minimum-system board and give me a layout fix list.

Content matches the files inside the package; extracted by the publish pipeline.

ESP32 最小系统 PCB

以 ESP32-WROOM-32E 模组为核心画一块可下载、可量产的最小系统板 (USB-UART 下载电路 + 3.3 V 电源 + 复位/Boot 按键)。模组内置 40 MHz 晶振、flash 与匹配好的天线,外部电路极少。

1. Brief 确认

  • 供电方式:USB 5 V / 外部 5 V / 直接 3.3 V
  • 下载方式:板载 USB-UART(CH340C / CP2102N)还是外接排针
  • 板框尺寸与天线朝向(模组天线端必须伸出板边或悬空)
  • 是否需要电池供电(决定是否加 LDO 静态电流约束)

2. 原理图要点

严格按 references/esp32-min-system.md 执行,重点:

  1. 3V3 轨峰值电流能力 ≥ 500 mA(Wi-Fi 发射瞬时电流), AMS1117-3.3 或 ME6217 均可,输入/输出电容按数据手册。
  2. EN:10 kΩ 上拉 + 1 µF 对地电容(上电延时),复位按键并联电容。
  3. GPIO0:10 kΩ 上拉 + Boot 按键到地;GPIO2 悬空或下拉, GPIO15(MTDO) 保持默认上拉。
  4. 模组 3V3 引脚旁 22 µF + 100 nF,100 nF 最近。
  5. UART0:U0TXD=GPIO1、U0RXD=GPIO3 接 USB-UART,交叉连接。
  6. 自动下载电路(DTR/RTS 双三极管)按参考文档连接,避免 GPIO0 与 EN 时序竞争。

3. 布局

按 references/placement-rules.md:

  1. 模组天线端放板边,天线正下方与前方 15 mm 禁布(所有层)。
  2. 去耦电容 100 nF → 22 µF 顺序贴近模组电源引脚。
  3. USB-UART 与按键放板另一侧,UART 走线远离天线区。
  4. 模组 GND 焊盘打 ≥ 6 个过孔到完整地平面。

4. 摆放自动检查

布局完成后导出/保存 .kicad_pcb,填写摆放计划并运行:

# 用 KiCad 自带 Python(Windows: KiCad\bin\python.exe)
python scripts/place_check.py --board board.kicad_pcb \
  --plan scripts/fixtures/placement-plan.json --tool-version 8.0.9

脚本检查:天线禁布区内是否有其他元件、去耦电容到模组的距离。 输出 edaskills.report.v1 报告;error 必须修完再投板。 嘉立创 EDA 用户按同一份 placement-rules.md 人工核对相应项。

Rules

  1. Strapping 引脚(GPIO0/2/15)默认电平不得改动,除非用户明确 要求并理解下载模式影响。
  2. 不打印、不存储任何 API key;本 Skill 不需要第三方凭证。
  3. place_check.py 只能在真实板文件上运行;没有 KiCad 环境时 明确告知,不得编造检查结果。
  4. 投板前提醒用户核对 JLC 组装库中模组与 USB-UART 的库存与封装。

What you get

  • An ESP32-WROOM-32E minimum-system layout workflow
  • Strapping-pin and EN reset-circuit wiring checks
  • Antenna keep-out and decoupling-placement checks (pcbnew script)
  • A fab-ready minimum-system board layout checklist

Good fit for

  • Minimum-system boards around the ESP32-WROOM-32E module
  • Engineers new to ESP32 hardware who want to avoid boot/antenna pitfalls
  • KiCad or JLC EDA workflows

Not for

  • Other modules such as ESP32-S3/C3 (different pins and RF)
  • Multilayer high-speed boards or RF front-end matching
  • Real placement checks without a KiCad board file
Before you start

You provide

  • A KiCad board file (.kicad_pcb) or schematic
  • Power source (USB / external 3.3 V) and programming-interface needs
  • Local KiCad ≥ 8.0 and Python ≥ 3.9

Environment

  • kicad ≥ 8.0
  • python ≥ 3.9

Last tested

No demo-run record yet.

Dependencies

Demo run

No demo run
Demo artifacts and verification reports appear here once a package includes them.

FAQ

Ratings & reviews

Not rated0 ratings

5 star0
4 star0
3 star0
2 star0
1 star0

Sign in to rate this skill.

Sign in

Versions

  • v1.0.0Latest6.5 KB

    首发种子版本。

    License: MITSourceSHA-256: f5ed2f09aa9bc780…

Related skills

No related skills
Skills with the same output type and use case will appear here.