Skip to main content
ComponentFreeNewv1.0.0

去耦电容选型

目标阻抗法去耦网络选型:按瞬态电流与纹波预算算 Ztarget,结合 MLCC 降额、ESL/ESR 与自谐振频率给出电容组合与数量,输出契约报告。

Installs: 1Rating: 5.0 (1)Updated:
Claude CodeGeneric

Badges only claim the demo-run passed on that host; cross-host installation is handled by the adapter layer.

Preview gallery

You say
Select decoupling caps for a 1.0 V core rail: 5 A transient, 30 mV ripple budget; give me an MLCC bank and counts via the target-impedance method.

Content matches the files inside the package; extracted by the publish pipeline.

去耦电容选型

用目标阻抗法(Ztarget = ΔV / ΔI)为每条电源轨选去耦网络, 而不是"每个电源引脚放一个 100 nF"的经验法则。

1. Brief 确认

每条轨需要:电压、瞬态电流阶跃 ΔI(A)、允许纹波 ΔV(mV)、 电流边沿时间(ns,决定频谱拐点 f_knee = 0.35 / tr)。 MCU 轨可用数据手册的 active/sleep 电流差;FPGA/SoC 核轨 用厂商 PDN 工具给出的瞬态值。拿不到就向用户要,禁止编造。

2. 计算选型

node scripts/cap_select.mjs --rails rails.json --out-dir out

rails.json 格式见 scripts/fixtures/rails.json。脚本:

  1. Ztarget = ΔV/ΔI;f_knee = 0.35/tr。
  2. 对候选系列(100 nF/1 µF/4.7 µF/22 µF/100 µF,含典型安装 ESL、ESR 与直流偏压降额系数)算 f_knee 处单颗阻抗。
  3. 选阻抗最低的高频电容,数量 N = ceil(Z_single / Ztarget)。
  4. Ztarget < 100 mΩ 时追加聚合物 100 µF + 22 µF 储能,并提示 大小电容并联的反谐振风险(需 PDN 仿真复核)。

产出 out/selection.csv + pdn-impedance.svg(首轨 PDN 阻抗曲线)

  • stdout 契约报告。

3. 落地建议

  • N 颗高频电容分布到各电源引脚,100 nF 最近引脚;过孔电感 计入安装电感(脚本的 ESL 已含典型安装值,见参考文档)。
  • 降额系数是估计值:正式设计用厂商 DC-bias 曲线(Murata SimSurfing / TDK)复核有效容量。
  • N > 8 或 Ztarget < 5 mΩ:板级去耦已到极限,建议改用更低 ESL 封装(0201/反转封装)、埋容或芯片封装内电容。

Rules

  1. 输入必须来自真实数据手册/厂商工具;无数据先要数据。
  2. 不打印、不存储任何 API key;本 Skill 不需要第三方凭证。
  3. 模型是集中参数近似,> 500 MHz 或电源平面腔体效应显著时 必须建议 PDN 场仿真,不得声称"精确达标"。

What you get

  • Target-impedance Ztarget calculation (transient current + ripple budget)
  • A capacitor bank accounting for MLCC derating, ESL/ESR and self-resonant frequency
  • Count and parallel scheme per value/package
  • An edaskills.report.v1 contract report

Good fit for

  • Power-distribution-network (PDN) decoupling for FPGA/MCU/SoC
  • Hardware/layout engineers quantifying a capacitor bank by target impedance
  • Power-integrity pre-review in any EDA tool

Not for

  • Full-frequency PDN impedance simulation (needs S-parameter/field tools)
  • Low-frequency bulk storage dominated by tantalum/electrolytic caps
  • Replacing the chip vendor official decoupling recommendation
Before you start

You provide

  • Supply voltage, transient current and allowed ripple
  • Target frequency band and available capacitor series (value/package/ESL/ESR)
  • Local Node ≥ 20

Environment

  • node ≥ 20

Last tested

v1.0.0 · Claude Code · Ran 2026/11/18

Dependencies

No dependencies
This skill works standalone.

Demo run

Passed with warnings0 errors · 1 warnings

edaskills-cap-select 1.0.0 · 2026/11/18

  • [info] RECOMMENDATION (3V3_MCU): 5 x 100nF (0402, SRF 20 MHz) for Ztarget 165.0 mohm; bulk: none
  • [info] RECOMMENDATION (1V2_CORE): 6 x 100nF (0402, SRF 20 MHz) for Ztarget 50.0 mohm; bulk: 100uF polymer + 22uF
  • [warning] ANTI_RESONANCE (1V2_CORE): bulk + HF mix can peak between SRFs; verify with PDN simulation or VNA measurement

FAQ

Ratings & reviews

5.01 ratings

5 star1
4 star0
3 star0
2 star0
1 star0

Sign in to rate this skill.

Sign in

Versions

  • v1.0.0Latest7.9 KB

    首发种子版本。

    License: MITSHA-256: f47b5f30ed1c355f…

Related skills

No related skills
Skills with the same output type and use case will appear here.